A ClearBuffer or ReportValue is a fill the GPU makes where it stands in the stream, and guest memory has its bytes once the GPU got there. A counter report reaches guest memory as a CPU write after its submission's fence, and a render condition reads the record when it is replayed. So a report followed by a clear of the same record ended as the report (in one submission always, across two when the completion thread was behind the GPU), and a condition replayed after the clear read what memory held before the fill, or the 0 of the report the clear had overwritten.
A clear of at most 256 bytes into CPU-visible memory is now also applied at its place in the replay to the records it covers that a counter report went into: the covered bytes get the value in guest memory at once, reports replayed before the clear leave those bytes alone when their write comes, a condition reads them from memory, and a report replayed after the clear writes the whole record as before. The GPU's fill is recorded as before. Other small clears stay the GPU's fill alone: the GPU reads guest memory too, at once in an imported pool and through the next upload of the written page in a mirrored one, so a write ahead of it into a draw count or an atomic counter would reach passes that still want the old value. NX2NAVI_CLEAR_SMALL_CPU=0 turns it off.
Whether the game clears counter records is not known. The pass timing captures of 75 scripted runs show one buffer fill a frame and nothing else about it, and the frame dump does not list buffer fills. The periodic vk_usnap line now counts the small clears, the last one's size, value and address, how many covered a record with a report, the reports into bytes cleared before, and the report writes that left cleared bytes alone.
Checked with a build of the dev exe, the launcher tests, the device address table check, and a scratch link of vk_exec_xfer.c against stubs that replays reports and clears in both orders. Not run in the game.
Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
A frame that was not rendered when it was due stayed lost: the timer set its
deadline to now once it was more than 100 ms late, and the device-paced path
only filled the ring to its target again, so after every gap the sound was
heard that much later than the picture it belongs to.
Frames that are owed are now rendered and dropped: mixed in full, so the
voices, the effects and the sinks the game reads back advance, and not queued
for the device, whose queue is filled to the same target afterwards. While the
device paces, what is owed is the silence it played for want of frames,
counted in its own samples from an underrun until the prefill is queued again;
the wait for the first prefill and anything owed across a stop do not count.
On the timer a frame is owed when its deadline passed a whole frame ago. A gap
of more than 3 seconds is not caught up: the sound goes on from now.
NX2NAVI_AUDIO_CATCHUP=0 turns it off and keeps the old timing. The audio
statistics line counts the catch-up frames and the gaps that were too long,
and tests/audio_mixer_check.py checks the device's side of the accounting.
Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
The mixer applied each voice's mix volume and each splitter destination's
volume to a whole 5 ms frame as one constant, so the level jumped at the
frame's first sample whenever the game moved a volume, which is heard as a
click. It now keeps what each voice and each splitter destination was mixed
with in the frame before and goes from there to the new value in equal steps
across the frame's samples, as the console's renderer does. An unchanged
volume stays on the constant path.
A voice that has just started, one that was silent in the frame before or was
moved to another mix or splitter, a destination that is new or was moved, and
the first frame after the renderer starts take the new volume at once.
NX2NAVI_AUDIO_RAMP=0 turns the ramps off. The audio statistics line counts the
render passes that ramped a volume. tests/audio_mixer_check.py builds the
mixer with the rest of the runtime stubbed and checks the ramps and the cases
that must not ramp.
Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
With flight = 1 and its thumbnails kept, the recorder now also writes a dump when a frame's picture differs strongly from the frame before and the frame after while those two agree, which is what a one-frame flicker looks like. Each thumbnail is reduced to 16x9 cells of mean brightness where the present thread already sees it complete, and a frame is a flash when at least three cells are more than 24 of 255 brighter or darker than in both neighbours, the neighbours being alike in those cells, around them and over the picture as a whole. A camera cut, a fade, a pan and shapes crossing the picture are no flash, and a frame beside one without a thumbnail is not judged. The dump is the one F8 writes, named "flash" with the frame's number in its header line, at most one every 30 seconds. flight_flash = 0 turns it off; flight_flash_diff and flight_flash_cells set the two thresholds.
On the thumbnails of earlier dumps the defaults flag the frames whose scene was white once and nothing in the runs without that fault. tests/flight_flash_check.py checks the test itself on drawn pictures.
Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
The stand-in for the game's upscaler enlarged the scene with a linear filter, which is softer than the console's picture. It now enlarges with the edge-adaptive filter the present already scales to the window with: the same shader, built a second time with a constant set so it squares what it filtered, as the linear pass does. The stored square-root values are filtered as before and the decode is the same. standin_filter = bilinear brings the linear pass back, and the setting is live. The linear pass also stays where nothing is enlarged and while DLSS or FSR 3.1 runs, since that upscaler scales the scene itself and its picture goes over the stand-in's. The movies do not go through this pass and are not changed.
Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
The water renderer runs trunc(step) times the water's substeps of its ripple simulation a frame, which is none while the step is under one frame: the rings stood still above 60 fps. A new site of the set ostep hands the cut to frame_rate_water_host, which adds the step to a remainder kept for the water object and returns the whole steps in it. The waters have a table of 64 slots of their own, as fewer slots than surfaces would have them take each other's in turn.
frame_step_check.py calls the water and day hooks as their sites do. It also gets the three platform stubs it has lacked since the day clock's hook, without which it did not link.
Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
The log thread wrote as soon as it woke, which outside a burst is once for every line: each line woke it and was a write of its own to the log file and the console. It now waits a quarter of a second from the first line it finds, or until the queue is half full, and writes what was queued by then at once, so the log is up to that much behind the game. What is being gathered stays in the queue, so a fatal error, a crash report and an exit write it out before their own lines as before; a game ended from outside loses those last lines. The queue's test checks the gathering, the half-full write and that a process which ends at once, by an exit or as a fatal error does, leaves every line in its file.
Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
The settings had a tab of their own; they are rows of the Game tab now, listed under the switch once the mode is on after a restart, and the tab is gone. With the mode off every one of them reads as unset, whatever nx2navi.ini or the environment says, so nothing of the mode acts unless a player turned it on; the build reads guest_opt the same way. The notes describe that, and take the white edges in towns and the dropped textures from the known issues to the fixes.
Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
A registration the game made while a submission was being replayed changed the slot table under that submission,
whose texture pool set is written as the replay goes and read when it runs. Such a registration now waits and takes
effect once the submission has gone to the queue; with the replay on its own thread it goes into the replay queue
ahead of the next item. NX2NAVI_REG_ORDER=0 restores the old behaviour. In a town session the white kerb, stair and
wall-top edges of single frames were gone with it; the log counts the registrations that waited.
Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
The row sets low_end_gpu, read at start, and says what the mode turns on and that it was measured on one card; its text is there in the menu's four languages. The key is decided again once the settings file is read.
Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
Mesh shaders as compute, the texture that gets memory of its own, staged mirror uploads and the shorter wait for the GPU, widened write-watch queries, the video memory limits and reserve, early upload batches, the asynchronous replay, the hot-pool rule and the recording thread on AMD cards without mesh shaders were measured on a Radeon RX 580 and run on no other card. Each keeps what 0.9.1 did unless the key or its own setting says otherwise; the key gives the defaults the way the device profile does. The notes describe them as that option, hold main's two new entries in one Changed section, and list the white edges in towns as a known issue.
Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
FSR 3.1 was soft at Performance and Ultra Performance, most of all in motion. On a village save, while the camera turned at a steady rate (present screenshots every 0.4 s, the mean absolute Laplacian of the scene's luminance): FSR 3.1 Native AA 6.7, FSR 4 Performance 5.9 and Ultra Performance 5.4, FSR 3.1 Performance 4.0 and Ultra Performance 3.3. The library's own input checks found nothing wrong, and its tuning constants (velocity factor, accumulation per frame, shading change scale, behind the test switch NX2NAVI_FFX_KEYS) gave nothing or took detail away. Its own sharpening at 100 instead of the default 80 gave 5.0 and 4.1.
Now the share of extra sharpening grows from none at three quarters of the output's width to all of it at half (vk_dlaa_fsr3_boost). FSR 3.1's own sharpness goes that share of the way to its maximum, and its picture gets a second RCAS pass (shaders/dlaa_sharpen.comp, AMD's FSR 1 header with the linear light taken through c / (1 + max c) and back), before the HUD is drawn. Both follow the sharpness slider; 0 turns them off, and NX2NAVI_FSR3_SHARPEN=0 leaves the second pass out. At RCAS's full strength the pass took Performance to 8.2, past Native AA, with grain on every surface, so it runs 1.5 stops weaker: Performance 5.7, Ultra Performance 4.7, Quality 5.2. 63.4 fps against 65.1 without the pass. The HDR picture is clean. FSR 4 is untouched.
Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
The camera kept its height (only ZR and ZL changed it) and rose whenever the closest surface in the lower part of the view came within about three metres, so flying up to a character, a rock or a wall sent it upwards. It now moves where it looks and nothing stops it, the ground included.
Ground avoidance is a checkbox in the debug menu's free camera section. With it on, the nine view distances read back from the lower view become points of the scene (from the view's angles and the camera's pitch), and only a column whose lowest surface rises by less than about 30 degrees counts as ground: the camera goes no lower than a metre above it. Steeper things, objects and walls, are left alone. The read-back runs only while the switch is on.
Tested on a village save, 4 m/s forward for 5 s and then ZL for 4 s: with avoidance off the camera ended 17.4 m lower, through the floor; with it on it ended 0.7 m lower and held there. Flown at Link with the first version of the ground test, its height did not change.
Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
The game's scene upscaler samples the post pass's picture through an RGB9E5 texture at the scene target's address. On the console both are one memory; here they are two images, and the RGB9E5 one kept what it held when it was made. With NX2NAVI_NATIVE_TENSOR=1 the network therefore read an old picture or the target's R11G11B10F words as shared-exponent texels, the source of the infinities and noise it wrote. The stand-in already read the target's image for this reason. A network program's output image without storage use is now logged.
Only dispatches of tensor-core programs take the new path, and those run only with NX2NAVI_NATIVE_TENSOR=1, which stays 0 by default. The file compiles without warnings; no game run has checked the picture.
Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
vk_dlaa_fg_inputs hands out DLSS's new history with the frame's depth and motion, and FSR 4's and NVIDIA's frame
generation pass it on, but vk_fg_frame dropped it: FSR 3.1 takes a cut only in the generation callback, which its
swapchain calls later on its own thread. vk_fg_frame now notes each frame id's cut in a small ring
(runtime/vk_fg_reset.h), and generate sets the callback's reset from it. A frame after one that was not prepared (the
menu open, no inputs) counts as a cut too, and so does an id the ring no longer holds.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The game's line width was dropped at the call and every line drawn 1 pixel wide; the game draws two lines a frame at 4.5 pixels into a 144x144 mask. The width is now recorded with the draw state and set as dynamic state for draws of the line topology class, held to the device's range. Only pipelines of that class list the new dynamic state, so the others keep their entries in the pipeline caches and the driver's. line_width = 0 draws every line 1 pixel wide as before.
Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
vk_dlaa_fg_inputs hands out DLSS's new history with the frame's depth and motion, and FSR 4's and NVIDIA's frame
generation pass it on, but vk_fg_frame dropped it: FSR 3.1 takes a cut only in the generation callback, which its
swapchain calls later on its own thread. vk_fg_frame now notes each frame id's cut in a small ring
(runtime/vk_fg_reset.h), and generate sets the callback's reset from it. A frame after one that was not prepared (the
menu open, no inputs) counts as a cut too, and so does an id the ring no longer holds.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
With the HUD hidden the screen showed the scene at its render size instead of the upscaler's picture. The upscaler ran at the pass after the game's own upscaler, taken for the pass the HUD is drawn into. Without a HUD the game draws no such pass: the next one is the frame's last, which encodes the stand-in's scaled scene into the 8-bit output. The upscaler's picture went into that target and the last draw drew over it. A player's save with the HUD off showed blocks of render pixels, a picture jumping by a render pixel between frames, and the undrawn edge row in white, at every FSR mode and at Native AA; every test save until now had the HUD on. vk_dlaa_upscaler now runs the upscaler right after the stand-in of the game's upscaler wrote its output image, and puts the picture there (NX2NAVI_DLAA_AT_UPSCALER=0: as before).
The edge fill moves to the end of each pass that took the jitter (vk_dlaa_pass_end), for the pass's colour targets and depth, in one copy of eight regions per image. Filled only before the upscaler, the undrawn row had already been read by the water, the bloom and the anti-aliasing pass.
On a copy of the player's save (HUD off), FSR 4 Ultra Performance, world slowed to 1/20, present screenshots 0.25 s apart: the picture moves 0.00 to 0.02 px between shots (old placement: a jump of one render pixel in 5 of 20), the change on edges is 1.9 against 16.9, and no shot has the white row (half had it, with HDR on). Native AA, Performance with HDR, and FSR 3.1 are steady and clean as well; the save with the HUD on is unchanged. A run through a stream: 0 of 106 shots with a bright bottom edge (20 of 102). Frame rate 58.3 fps against 58.6.
Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
A player's clip at Ultra Performance still showed the sky's colour in the last row of about half the frames. In those frames the fill, done only after a jitter to the left or up, had not run. The outermost row and column on each side of the light target and the depth are now filled from their neighbours whenever the frame was jittered, whatever the jitter's direction. A copied border pixel is nothing anyone sees.
A quick swing of the camera around Link turns it 11 to 18 degrees and moves it 0.9 to 1.4 m a frame. That was taken for a cut, and nine frames in a row started a new history, which showed the scene at its render size, blocky at the smaller modes. A cut now needs a move of 5 m or a turn of 30 degrees with a move.
Hyrule Field, FSR 4 Ultra Performance, present screenshots: standing still and on grass while running, the bottom edge matched the rows above it. Over water a bright bottom edge remains in a fifth of the moving shots, and none with the jitter off: the water reads the scene before the fill. The 0.9.2 notes list it as a known issue, with the frame rates and FSR's GPU times measured for the Ultra Performance question.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The game's line width was dropped at the call and every line drawn 1 pixel wide; the game draws two lines a frame at 4.5 pixels into a 144x144 mask. The width is now recorded with the draw state and set as dynamic state for draws of the line topology class, held to the device's range. Only pipelines of that class list the new dynamic state, so the others keep their entries in the pipeline caches and the driver's. line_width = 0 draws every line 1 pixel wide as before.
Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
The 0.9.1 notes keep the release branch's text and take main's sections: New, the edge line under Fixed, and Changed.
Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
The 8 ms and 16 ms tried in their place left fewer draws out in a scripted walk, but in play a frame that takes 10 to 14 ms longer felt worse to the player than one that is left out, in two sessions on the same install. The wait stays counted once for each pipeline, and a frame that has left a draw out already still waits for nothing more.
Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
Such a frame is held back or shown without that draw whatever its other pipelines do, and with hundreds of pipelines new at once every frame of an area's load spent its whole 16 ms budget on waits that could not complete it: 49 frames over 25 ms in a walk with no pipeline recorded, against 17 with the earlier 3 ms waits. With the rule the same walk has 15, the picture stands still 15 times instead of 50, and 1 frame is shown incomplete instead of 22.
Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
A draw that met a new pipeline waited 3 ms for its fast link, in every frame, which is just under what the link takes with the stage libraries in the driver's cache: in a first-visit session on a new install 66 of 87 such draws gave up at the end of the wait and their frame was held back. The wait is now 8 ms for each pipeline, counted from its first miss and shared by all its draws, and 16 ms for a frame, so a pipeline the driver has to compile costs one frame the wait and the frames after it nothing.
The pipeline list tool also takes the compute variants a game folder dispatched, which no pipeline record names and which were translated in the middle of play, and reads a list made before as one of its inputs.
Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
0.9.0 is tagged at fbd4067 without the launcher's Mods screen, which came after it (89c453d), so its bullet goes under "New" in docs/releases/v0.9.1.md, unchanged. docs/releases/v0.9.0.md is back to how it was at the tag.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
With FSR 4 or FSR 3.1 a light line flickered along the bottom and right edges of the picture. The jitter moves the scene's viewport by under half a pixel, which keeps every pixel centre inside it. Yet on an RX 7900 XT, a viewport moved up left the last row undrawn in every scene pass, and one moved left the last column. A frame dump showed the depth's last row at its clear value and the light target's last row holding the fog's colour, which the upscaler blended into the edge. NX2NAVI_DLAA_EDGE_FILL=0 turns the fill off for testing.
Hyrule Field, 3416x1440, present screenshots: the outermost rows averaged 40 against 20 just inside without the fill, and within 1 of the inside with it. The same held with FSR 4.1 Native AA and Quality, FSR 3.1, SMAA and HDR. Jitter off, and no upscaler, gave no line either.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Choosing one of them while a temporal upscaler was set turned the upscaler off, and the picture fell back to bilinear scaling. vk_aa.c no longer keeps the game's SMAA while DLSS or FSR runs. The chosen pass replaces the game's composition as without them: in the native modes after the upscaler, and in the scaling modes before it. In the menu, a choice leaves the upscaler and frame generation alone, and the row notes that the upscaler's TAA runs too. Picking DLSS or FSR under Upscaling keeps the Anti-aliasing choice. The TAA entry, listed while no temporal mode is set, now sets FSR 4 Native AA where FSR 4 runs instead of forcing FSR 3.1. The overlay gets an Anti-aliasing line under Upscaling, for example "TAA + SMAA (Ultra)".
Checked on an RX 7900 XT in Hyrule Field with FSR 4.1 Native AA and Quality, and with FSR 3.1. The log has "the game's SMAA replaced by" smaa, off and fxaa while FSR 4.1.2 upscales, and the pictures are right.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Mods, on the home screen, opens the game's mods folder, adds a downloaded mod from its .zip, .7z or .rar file or its
folder, switches each mod on or off, and sets the load order (mods_disabled and mods_order in nx2navi.ini, written as
the game writes them). Each mod's description says what it changes, which other mod changes the same files and which
of the two wins, and why the game leaves it off when it does.
Before the game starts, Play puts the mods folder in order (launcher/mods.py prepare): an archive in it is unpacked into
a folder of its name and kept, a mod whose files sit a folder or more down has them moved up, and a romfs, exefs or
cheats folder put straight into the mods folder becomes a mod of its own. An archive that would write outside its
folder is refused, and nothing is deleted.
The launcher's build (tools/make_game.py) left the mods' code cheats and ExeFS patch files out, so those mods stayed
off. The lift now turns them into patch sets first, as the setup does, with the files in the lift's key and
build-cache/mod-code.json recording what it took up. Play builds the game again before it starts when an enabled mod
brings code no build has seen. The shaders' key names the lift and the compile without the mods' code, so such a build
compiles only what the patches change and leaves the shaders prepared. tools/mod_files.py is the one place the tools,
the build and the launcher find a mod's parts.
Tested: a zipped mod holding its own folder, put into a mods folder, was unpacked and moved up by the launcher's code,
and the game served its file in place of the game's. The lifter took a code cheat and a pchtxt patch made for the game's
main as patch sets. The launcher's and the setup's tests pass.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The coordinate pair and the absorption guard needed modules made on each PC by tools/projective_recipe.py and a folder named in NX2NAVI_SPV_OVERRIDE, so no player had them. runtime/spirv_water.c makes the recipe's edits on the translation in memory, in the recipe's order: on the NVIDIA profile its three modules are byte for byte the recipe's (RTX 5090, game 1.1.1). vk_pipeline.c keeps the edited modules in a small table, made at first use, and builds a pair from them only when both of its stages were made; a module of another shape is built as it is, with a log line. NX2NAVI_WATER_PROJECTIVE=0 turns the corrections off. tests/water_projective_check.py compares the runtime's edits with the recipe's on made-up modules.
Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
Run from a checkout, the launcher uses the Python that started it. A Python older than 3.14 without the zstandard
package got through the first-run screen and stopped at Gather Build Tools with only "No module named 'zstandard'",
after the packages were downloaded. toolchain.zstd_missing now looks for compression.zstd or zstandard when the
launcher starts. Without either, the log and the first screen name the Python and give the pip line for
tools/requirements-launcher.txt, and Gather Build Tools stops with the same message before it unpacks anything. A
release's own Python always has the package; if it ever lacks it, the message says to reinstall NX2navi.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
With Hide Launcher While Playing off, the launcher stayed in its normal state behind the game and kept stepping its
animations: about 0.6 of a CPU core went to a window nobody saw, beside the game's render thread. The animations now
also stand still while the window is not in front, the same check the gamepad polling uses.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The paired modules were looked up by the hash of the module as built, so a vertex module that had outputs added for its union (which differs from one install to the next) or a fragment module changed for dual-source blending ended the run. The vertex replacement now stands for the translation itself and takes the added outputs as any module does; a pair with dual-source factors is built from its original modules in both stages.
Co-Authored-By: Claude Fable 5.2 <noreply@anthropic.com>
Add the exact-material nonnegative distance guard and the recorded NVIDIA translation profiles. Keep generated shaders and the private native patcher out of the repository. Document reported cross-vendor testing and the unresolved origin of invalid absorption distance.
Carry clip coordinates through perspective interpolation for the identified water shader pair. Keep generated modules private and document the observed results and remaining portability limits.
A new install met every pipeline in play: in Hyrule Field one 600-frame stretch of a first visit had 1,769 draws wait 461 ms in all for pipelines, the longest frame 88 ms. The boot now reads seed-pipeline-keys.bin, the release's list, as recorded pipelines after the install's own (keys_open_seed, NX2NAVI_PIPE_SEED, default 1): their pairs go into the vertex output unions and the prewarm builds them as it builds the install's. The preparation builds every listed pipeline (NX2NAVI_PREPARE_PIPELINES now defaults to all), with the unions of the same list, so the first boot of a new install finds them in the caches. The list's mesh pipelines are left out at the boot on a GPU without mesh shaders, as the preparation leaves them out. Nothing of the list goes into pipeline-keys.bin.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The game finalizes texture objects on its own thread ahead of the replay, which still draws the frame the game recorded
before that; on the console the memory still holds the texels those draws read. Kakariko moves about 30 of its
textures to new addresses every four or five frames, and each move finalized the old descriptors. The replay's draws
of the frame before then met finalized CPU-written slots, and the stale rule gave them the stand-in even when their
own entry was still there with its content. The village's haze dropped out of a frame a few times a minute, and the
haze sprites that met a stand-in left hard-edged clear patches. A play session in Kakariko logged up to 4,805 stand-in
lookups in 60 frames, 1,826 in the 60 frames around one haze dropout, and 612 in the 60 frames after a run of
patched frames.
Such a slot now resolves to its own entry while that entry was uploaded or drawn by the GPU, and was neither superseded
by another descriptor at its address nor overwritten. The lookup samples the image as it is: it neither takes the
entry back nor reads its storage, so freed storage is still never read (the access violation the stale rule was made
for). NX2NAVI_TEX_STALE_KEPT=0 gives the stand-in again. The perf log's finalize line counts these lookups.
In a replay of a recorded Kakariko walk, most 60-frame windows went from stand-ins to the kept image (up to 328 a
window, stand-ins 0). In play, stand-ins remain in short bursts where the entry was already gone (up to about 2,000 in
60 frames, against the kept image in most windows). The tester still sees flicker that the 640x360 frame recorder
does not catch; that is not settled by this.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The BC3 encoder's colour half is a four-colour BC1 block (c0 above c1, or every index 0 when they are equal), so a BC1 image of an opaque texture decodes to exactly the texels the BC3 one did. The encoder writes that half alone with its specialization constant BC1 set; its push constants are as before, so the BC3 pipeline is unchanged.
Every ASTC texture the CPU provides is made BC3, and its first upload checks its blocks while it copies them into staging: when all decode with alpha 255 (tex_astc.c astc_blocks_opaque, from the block header for all but the endpoint modes with alpha, which are decoded), the entry gets a BC1 image in place of the BC3 one before the decode. Later uploads into a BC1 image check again and go back to BC3 for content with alpha. A large texture's copy and check run on the ASTC decode workers, so its first upload copies faster than before. A check of its own where the texture is made cost 1.7 s of the render thread over a seven-minute teleport tour.
On that tour (Kakariko Village, the Graveyard, Death Mountain Trail, Kokiri Forest, Hyrule Field, RX 7900 XT), against BC3 alone in the same batch: the ASTC textures in Hyrule Field at the end 2,568 instead of 3,104 MiB, video memory at its peak 11,814 instead of 12,374 MiB, process commit at its peak 25,539 instead of 26,139 MiB; the first 7,200 frames in 93.7 instead of 101.3 s and the run's slowest 1 % at 24.1 instead of 21.1 fps. --probe-astc checks the header test against a decode of every generated block, the loop, its copy and the worker pool against it, and each BC1 block against the colour half of its BC3 block. NX2NAVI_ASTC_BC1=0 (astc_bc1 = 0) keeps every ASTC texture BC3; the sampling probe NX2NAVI_ASTC_BC_PROBE it replaces is gone.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>